KENWOOD TM-V7A OPERATING MANUAL Transceiver Tour Starting at top left and proceeding around transceiver counter clockwise On left Call VFO MR - Memory Bottom Tuning on bottom. Press top for 1 MHz steps, press and hold for 10 MHz steps Four buttons the left is F or function Two sets of Volume, center and squelch at base. Left is VFO and right is UHF. Push either for band select Right bottom to top MNU - Menu PM - Programmable Memory On/Off Microphone Tour With buttons facing you and PTT on the left Up and Down on top with Down on left and Up on the right Top,ost buttons above the standard 16 button keypad are as follows left to right - Call, VFO, MR and PF . I have yet to figure out what PF does as the default. Lock switch is on the back and I do not know the lock position. Reset Partial - resets all rig functions but leaves Memories intact. Turn rig off Hold VFO and turn rig on There is a visual message asking yes or no, press VFO to reset, any other key to exit Reset Full - resets rig and resets Memories Same as above but use MR instead of VFO Microphone Control The rig can be set to enable many control functions from the microphone. Method to set is outlined below and involves changing a Menu setting that is better done with sighted help. Manual states that nearby touch tones may interfere with rig performance. Functions that can be controlled are: Keypad 1 Visual scan Keypad 2 Tone/CTCss 3 Reverse 4 1 Mhx step 5 Monitor 6 Frequency readout memory channel ?? 7 Volume change * down # up 8 Dual band receive 9 Squelch * down # up 0 Transmit power change A Enter * Star - Frequency down # Pound - Frequency up To Activate Microphone Control Press MNU second button on right under the On/Off switch to enter the Menus Use tuning knob to go to Menu 16, Microphone is on the display On the display there is a right facing arrow above the third of the four buttons under the display. Press until display says Mic Control. If you go too far there is a left facing arrow under the second button to go back Press Set, the right of the four buttons to toggle the function On. Display says On Press MNU to exit the Menu mode. Frequency Entry - Direct Ensure Microphone Control is enabled, see above Select band and VFO Press A on the microphone The initial 1 for VHF or 4 for UHF is already entered. Enter the remaining 5 digits. Last digits must be 0 ot 5 for VHF or 00, 25, 50 or 75 for UHF. If you leave more than 10 seconds between any actions you get to start over. Memory Storing Enter desired frequency and settings in the desired band in VFO mode Press F the left button of the four under the display Use Tuning to select the desired Memory Channel Press MR. The VFO frequency and settings are entered in the selected Memory and any previous data in that Memory is overwritten. Do not leave pauses of mor than 10 seconds or you get to start over. Wait 10 seconds for the rig to reset itself. There is probably a button that will reset it immediately. Call Channel Loading Load frequency and settings in the VFO mode Press F the left button of the four under the display Press Call, any previous data is overwritten Menu Defaults The following lists the defaults available under the Menu System. These features can be changed but sighted help is required. The speech synthesizer does not provide sufficient audio information to allow changes without the ability to read the display. The following table shows the Menu Number, the itm number within each menu with multiple items, the descriptionand options, the default setting and the page number in the original manual. 1 - Transceiver Guide N/A 15 2 1 Number of channels for visual 49 41 scan 25/49/73/147 2 2 Power on message KENWOOD 69 2 3 Multi function buttons F/TONE/REVLOW 66 3 1 Display Reverse Negative 71 Positive/negative 3 2 Display contrast 1 min to 16 8 71 3 3 Display dimmer 1 man to 4, Off 1 70 3 4 Aito dimmer change On/Off Off 70 4 1 Memory channel lockout On/Off Off 45 4 2 VHF/UHF Memory Radio 90/90 29 90/90.110/70, 130/50, 140/140 4 3 Memory channel names None 32 4 4 Auto PM Channel storing On/Off Off 39 5 1 Auto repeater offset On/Off On 26 5 2 Offset freq. 0 to 30 MHz steps Standard offsets 24 5 3 Europe version only N/A for Canada and US 6 - Limit the frequency range over Full range 64 The rig will operate 7 - DTMF number storing Empty 59 8 - Scan resume time or carrier Timer operated 43 9 - Intermodulation reduction On/Off Off 62 10 - Auto power off On/Off Off 61 11 - Time out timer 2/5/10 minutes 10 min 61 12 1 DTSS/Pager code transmit delay 350 ms 52 350/550 ms 56 12 2 Auto Page cancel auto/manual Manual 57 12 3 Page answer back On/Off Off 57 13 1 S Meter squelch On/Off Off 68 13 2 S meter squelch time Off 68 125, 250, 500 ms and Off 14 1 Beep volume 1 min to 7 and Off 5 66 14 2 External speaker operation. See the manual 76 14 3 Voice synthesiaer language/Off English 82 15 1 Data transfer 1200/9600 bps 1200 bps 79 15 2 Data TX/RX band On/Off Off 79 16 1 Microphone control On/Off Off 77 16 2-5 Programmable Function Keys F/TONE/REVLOW 73 different functions 16 6 DTMF monitor On/Off Off 58 17 - Hold TX 500 ms after releasing On 81 PTT On/Off